---
title: Belt Support Solves Fugitive Dust & Spillage Problems
description: A coal plant had spillage and dust issues at two conveyor transfer points. Repeated downtime and increased labor costs seriously impacted plant production.
---

[Martin® Problem Solved Papers](https://blog.martin-eng.com/problem-solved-papers)

# [Belt Support Solves Fugitive Dust & Spillage Problems](https://blog.martin-eng.com/problem-solved-papers/belt-support-solves-fugitive-dust-spillage-problems)

 Written by [Martin Engineering](https://blog.martin-eng.com/problem-solved-papers/author/martin-engineering) | March 22, 2023 at 6:15 PM

### Problem

The Yanzhou Dongtan coal plant in Eastern China had spillage and dust issues at two conveyor transfer points because material was loaded onto the 40-inch (1000 mm) wide belts traveling 500 fpm (2.56 m/s) with little control over impact or [settling](https://foundations.martin-eng.com/learning-center/settling-zones-at-transfer-points). The result was excessive [fugitive dust](https://foundations.martin-eng.com/learning-center/learning-center/displaced-induced-and-generated-air) from belt #111 throughout the facility. Inadequate chute control on belt #185 caused spillage to get caught between the belt and rubber tail pulley, damaging both. Repeated downtime and increased labor costs for these issues seriously impacted plant production.

### Solution

After an on-site inspection, Martin Service technicians installed [transfer point solutions](https://www.martin-eng.com/content/product_category/469/conveyor-transfer-point-solutions) addressing both conveyors’ unique issues. On #111, a 16.5-foot (5 m) transfer chute distributed material into a 40-foot (12 m) long sealed stilling zone equipped with a full-length Martin® ApronSeal™ Skirting and a series of Martin® Slider Cradles. The 85-foot (26 m) chute on belt #185 required a Martin® Impact Cradle, Martin® ApronSeal Skirting™, and Martin® Slider Cradle support down the entire length. Both chutes featured a Martin® Dust Bag.

### Results

Since the installation was completed, visible dust within the facility has been drastically reduced. Respirable dust has been measured at less than 3.5 mg/m3, and total dust is down to 10 mg/m3. Operators report that onsite safety and the overall work environment have improved and that the significant drop in equipment failure rates has substantially increased plant productivity.

<https://blog.martin-eng.com/problem-solved-papers>

[View full post](https://blog.martin-eng.com/problem-solved-papers/belt-support-solves-fugitive-dust-spillage-problems)

```json
{
  "@context" : "http://schema.org",
  "@type" : "BlogPosting",
  "author" : {
    "@type" : "Person",
    "name" : "Martin Engineering"
  },
  "dateModified" : "2026-07-24T19:55:53.177Z",
  "datePublished" : "2023-03-22T18:15:45Z",
  "headline" : "Belt Support Solves Fugitive Dust & Spillage Problems",
  "image" : {
    "@type" : "ImageObject",
    "height" : 483,
    "url" : "https://5156573.fs1.hubspotusercontent-na1.net/hubfs/5156573/TransferPointSolutions.jpg",
    "width" : 646
  },
  "mainEntityOfPage" : "https://blog.martin-eng.com/problem-solved-papers/belt-support-solves-fugitive-dust-spillage-problems",
  "publisher" : {
    "@type" : "Organization",
    "logo" : {
      "@type" : "ImageObject",
      "height" : 60,
      "url" : "/hs/hsstatic/content_shared_assets/static-1.4092/img/default-amp-logo.png",
      "width" : 60
    },
    "name" : "Problem Solved Papers"
  }
}
```